Complete Guide on How to Improve SSD Read and Write Speed? [2023]

SSDs are like superchargers for your computer. They work way faster than old hard drives (HDDs), making your computer quicker and more responsive. But they can get slow or even stop working if you don’t care for them.

If your SSD is acting slow, don’t worry! Here’s a simple guide to help you make it faster. We’ll show you different ways to make your SSD read and write data faster. This will make your computer better for playing games and getting work done. So, why wait? Let’s make your computer faster!

Table of Contents

How to Make Your SSD Faster for Reading and Writing

Try all the solutions below to figure out what’s making your SSD slow. But if you already know the problem, use the fix that matches your SSD issue:

Make your SSD have more space by extending its partition.
Check if TRIM is supported and enabled.
Turn on AHCI mode to make your SSD work better.
Optimize your SSD to improve its performance.
Select the high-performance mode for your SSD.
Update your SSD’s firmware to the latest version.
Make sure your computer’s boot order is set correctly.
Check the SATA port and cable connecting your SSD to your computer.

Here are 8 easy ways to increase the read and write speed of your SSD.

Method 1: Expand Your Partition for More Space

Your SSD might have some unused space that can be added to the main storage area, giving you more room. This extra space can improve your SSD because it leaves room for the computer’s temporary storage needs.

You can do this using a tool that comes with Windows called Disk Management, or you can use another program from a different company. I suggest using EaseUS Partition Master because it can quickly format the unused space and add it to the main storage. This program has a special feature called “Extend Partition” that makes it easy to do this.

Method 2: Check If TRIM Is Enabled

Make sure your computer is using the TRIM command for your SSD. If it’s not, your SSD might not work as fast as it should. Follow these steps to check and enable TRIM:

Step 1. Open the “Command Prompt” as an administrator.

Step 2. Type the following command and press “Enter“:\

Note: If it shows 0, that means TRIM is already enabled. If it shows 1, that means TRIM is disabled.

Step 3. If you see 1, type the following command and press “Enter“:

Set TRIM to Enabled with this command: fsutil behavior set DisableDeleteNotify 0

Now, TRIM is enabled for your SSD. You can also use your SSD manufacturer’s software to do this.

Method 3: Turn on AHCI Mode for Faster SSD

AHCI, which stands for Advanced Host Controller Interface, makes your SSD work faster than the older IDE mode. You can switch to AHCI mode to get quicker SSD reading and writing.

Here’s how to do it:

Step 1: Open Windows’s “Command Prompt” as an Administrator.

Step 2: Type this command and press “Enter“:

Use this command: bcdedit /set {current} safe boot minimal

Step 3: Turn on the “AHCI” mode inside your computer’s BIOS settings.

Step 4: Save the changes and leave the BIOS to start your computer’s operating system.

Step 5: Open the “Command Prompt” when your computer is in Safe Mode and enter this command:

Remove Safe Mode with this command: bcdedit /delete value {current} safe boot

Your computer will restart, and AHCI mode will be set up automatically for the best SSD performance.

Method 4: Optimize your SSD to improve its performance.

Over time, your SSD can become slow because it collects many files and installs apps. To fix this and make your SSD work faster, you can do something called “optimizing” it. Here’s how:

Step 1: Look for “Defrag” in your Windows Start menu.

Step 2: You should see an option called “Defragment and Optimize Drives.” Click on it to open the “Optimize Drives” window.

Step 3: Pick your SSD drive and click the “Optimize” button. This will make your SSD work better.

Note: Making your SSD work better by optimizing it now and then is a good idea. You can even set it up to optimize itself automatically every month.

Method 5: Select the High-Performance Mode for your SSD.

Your computer might be trying to save power, which can slow down your SSD and overall performance. Switch your computer to the “Best Performance” mode in Windows to get your SSD working its fastest. Here’s how to do it:

Step 1: Open your computer’s “Settings” and find the “System” section.

Step 2: Click on “Power and Battery.”

Step 3: Look for the “Power mode” option under the “Power” tab.

Step 4: Select “Best Performance” from the list and turn it on. This will give your SSD and the rest of your system the most power and resources for the fastest speeds.

Note: Doing this will make your drives and computer work the fastest, but it will use more power and make your battery last less time.

Method 6: Update your SSD’s firmware to the latest version.

Updating your SSD’s firmware is important to prevent problems and improve your SSD’s work. Here’s how to do it:

Step 1: Visit the company’s website that made your SSD and find your SSD model.

Step 2: Download the new firmware and install it on your SSD.

After that, restart your computer, and your SSD will be up to date.

Method 7: Make sure your computer’s boot order is set correctly.

Another important thing to consider is the order in which your computer starts up, known as the boot order. You can check and change this by entering your computer’s BIOS settings. Set your SSD as the main boot drive for the quickest reading and writing speeds.

Doing this makes sure your computer gives the most importance to your SSD, making your system work faster and respond better.

Method 8: Check the SATA port and cable connecting your SSD to your computer.

Last but not least, make sure your SATA connection is secure and not loose. Open your computer’s case and check that the SATA cable is connected properly. Also, make sure the connector or port isn’t damaged.

If you spot any problems, replace the cable and use a new SATA cable in a different SATA port for the best performance.

It’s a good idea to monitor your SSD’s speed while you use it every day. You can use EaseUS Partition Master to do this:

Note: If the Methods we discussed earlier don’t make your SSD faster, you can try using special software called Remo Recover. It can help with different problems, including making your SSD work better. Give it a try and see if it helps your SSD go faster.

Why do SSD Read and Write Speeds Slow Down?

Let’s discuss why your SSD can become slow before discussing how to fix it. Sometimes, your NVMe SSD is not writing data as fast as it should. Here are some common reasons for a slow SSD and occasional errors:

Running out of space: Make sure your SSD has at least 20% of its storage space free. Your computer sometimes uses this space to work faster.

Missing TRIM command: TRIM is crucial for keeping your SSD and HDD working well.

Disabled AHCI mode: AHCI is like a bridge between your SATA SSDs and your computer.

Incorrect boot settings: How your computer starts up can affect your SSD performance.

Viruses: Viruses, malware, and spyware are bad news for your PC. They can infect your SSD and make it slower.

Outdated BIOS or firmware: Keep your computer’s BIOS up to date, and check for any new firmware for your SSD to keep it running smoothly.

Problems with SATA port or cable: Your SSD might slow down if the cable or port connecting it is loose or damaged.

Low RAM: Your PC’s RAM manages all its tasks. If you don’t have enough RAM, your SSD might slow down. Try closing background programs and restarting your computer to free up RAM.

Simple Tips to Boost Your SSD Read and Write Speeds

Here are some easy tips to make your SSD read and write data faster:

Keep Your Computer Cool: Ensure your computer stays at a comfortable temperature. When it gets too hot, it can slow down your SSD.

Keep Your Files Tidy: Delete stuff you don’t need and organize your files neatly. This helps your SSD work faster.

Back-Up Your Stuff: Regularly save copies of your important files. This way, you won’t have to use your SSD too much.

Update Your SSD: Sometimes, the company that makes your SSD releases updates. These can make it faster and fix any problems.
Use a Good Power Source: Make sure your computer gets steady power. If it suddenly loses power, it can hurt your SSD.

Conclusion:

In conclusion, if your SSD isn’t working as fast as it should or you’ve lost important files, there are steps you can take to improve its performance and recover your data. Optimizing your SSD, changing system settings, and even using software like Remo Recover to recover lost files. Remember that backing up your data regularly is essential to prevent future issues. You can enjoy a faster and more reliable SSD experience with the right steps.

Frequently Asked Questions:

What does SSD stand for?

SSD stands for “Solid-State Drive.” It’s a computer storage device that stores data electronically, making it faster than traditional hard drives (HDDs).

How often should I optimize my SSD?

You should optimize your SSD periodically, such as every few months, to maintain its performance. You can also schedule automatic optimization in Windows.

What is Remo Recover, and how does it work?

Remo Recover is software that helps recover lost or deleted data from SSDs and other storage devices. It works by scanning the drive for lost files and allowing you to recover them.

About the Author:

With a decade of experience in data recovery, John Harris, Senior Editor at Remo Software, is your go-to specialist. His focus includes partition management, Windows solutions, and data troubleshooting, delivering insightful content that serves both users and search engines. John’s expertise shines through in illuminating blog posts, untangling data loss intricacies across diverse storage platforms. His mastery extends from file systems to SD cards, USBs, and external drives on Mac and Windows. Recognized by cpomagazine, everythingusb, and more, John Harris is your trusted data recovery guide. You can also find his articles featured on correctblogger.com, computertechreviews.